日本SMC低速摩擦氣缸*現貨

日本SMC低速摩擦氣缸*現貨

由于汽缸結合面被蒸汽沖刷或腐蝕出溝痕，選用適當?shù)暮笚l把溝痕添平，用平板或平尺研出痕跡，研刮焊道和結合面在同一平面內。汽缸結合面變形較大或是漏汽嚴重時，在下缸的結合面補焊一條或兩條10—20mm寬的密消除間隙封帶，然后用平尺或是扣上缸測量，并涂紅丹研刮，直到消除間隙。此操作的工藝也很簡單，焊前預熱汽缸至150℃，然后在室溫下進行分段退焊或跳焊。選用奧氏體焊條，如A407、A412，焊后用石棉布覆蓋保溫緩冷。待冷卻室溫后進行打磨修刮。

日本SMC低速摩擦氣缸*現貨

MQMLB10-100D
MQMLB10-10D
MQMLB10-15D
MQMLB10-22D
MQMLB10-30D
MQMLB10-45D
MQMLB10-60D
MQMLB10-75D
MQMLB10H-100D
MQMLB10H-15D
MQMLB10H-30D
MQMLB10H-45D
MQMLB10H-75D
MQMLB16-100D
MQMLB16-15D
MQMLB16-20D
MQMLB16-22D
MQMLB16-30D
MQMLB16-45D
MQMLB16-50D
MQMLB16-60D
MQMLB16-75D
MQMLB16-80D
MQMLB16H-100D
MQMLB16H-15D
MQMLB16H-20D
MQMLB16H-30D
MQMLB16H-40D
MQMLB16H-45D
MQMLB16H-75D
MQMLB20-100D
MQMLB20-15D
MQMLB20-22D
MQMLB20-45D
MQMLB20-60D
MQMLB20-75D
MQMLB20H-100D
MQMLB20H-15D
MQMLB20H-25D
MQMLB20H-30D
MQMLB20H-75D
MQMLB25-100D
MQMLB25-10D
MQMLB25-15D
MQMLB25-30D
MQMLB25-45D
MQMLB25-50D
MQMLB25-60D
MQMLB25-75D
MQMLB25H-100D
MQMLB25H-15D
MQMLB25H-30D
MQMLB25H-75D
MQMLB6-15D
MQMLB6-20D
MQMLB6-30D
MQMLB6-45D
MQMLB6-60D
MQMLC20-100D
MQMLC25-100D
MQMLD10-60D
MQMLD16-100D
MQMLD16-15D
MQMLD16-30D
MQMLD16-45D
MQMLF20-75D
MQMLL20H-100D